TWI Digital Library

An empirical process model to estimate tool shoulder temperature for different materials and friction stir welding (FSW) conditions is described that incorporates a design of experiments method and linear regression analysis (MATLAB software) with c…

Haynes Alloy 282 (Ni, 19.45%Cr, 10.28%Co, 8.55%Mo) was deposited onto Inconel 600 substrates (Ni, 16.69%Cr, 9.36%Fe) using a cold-wire TIG process, subjected to additive friction stir processing (AFSP) to create gamma-strengthened surface layers, an…

With regard to the occurrence of coarse alpha-Al dendrites, eutectic phase, shrinkage porosity and other defects in cast aluminium alloys, an investigation was undertaken into the influence of different combinations of friction stir processing (FSP)…

2024-T3 aluminium alloy (Al, 4.4%Cu, 1.5%Mg) thin sheets (thickness 1 mm) were joined by friction stir welding (FSW), and the effect of process parameters (tool rotation speed and traverse rate) on the microstructure and mechanical properties of the…

Friction stir processing (FSP) experiments were undertaken on 7B04-O aluminium alloys (Al, 6.23%Zn, 2.88%Mg, 1.58%Cu) and the evolution of microstructure and mechanical properties in the stir zone was investigated. FSP was conducted using a tool mad…

With regard to the capability of ultrasonic vibration enhanced friction stir welding (UVeFSW) to improve weld formation quality as well as the microstructure and mechanical properties of the welded joints, experiments were undertaken to clarify the …

An experimental study was made of the effect of friction stir processing (FSP) and the influence of process parameters on the microstructure and mechanical properties of cast magnesium AZ91 alloy. FSP tests were conducted on die cast plates of 4 mm …

An investigation is presented into bead-on-plate friction stir welding of type 304 austenitic stainless steel (18.1%Cr, 8.56%Ni) and the relationship between corrosion properties and weld microstructure. Microstructural observations were performed b…

Square butt welds of AA 7075-T6 sheet (thickness 1.3 or 3.2 mm) to AA 7075-T6 extrusions were fabricated by friction stir welding (FSW) procedures incorporating the controlled introduction of defects, and the impact of the defects on joint mechanica…

In relation to the development of corrosion barrier capsules for spent nuclear fuel disposal, friction stir welding experiments were conducted on oxygen-free copper plate specimens (thickness 20 mm) using different joint preparation, shielding gas a…

With regard to the occurrence of coarse alpha-Al dendrites, eutectic phase, shrinkage porosity and other defects in cast aluminium alloys, an investigation was undertaken into the influence of different combinations of friction stir processing (FSP)…

With regard to inconsistencies in the literature concerning the correlation between friction stir welding (FSW) process inputs and post weld process or material response, an investigation is presented into the primary variables (temperature, cooling…

The microstructures and strengthening mechanisms during friction stir processing (FSP) of AZ91 (Mg, 9%Al, 1%Zn) die-cast and Mg-Y-Zn (Mg, 5.9%Y, 2.6%Zn and Mg, 5.5%Y, 4.3%Zn) cast alloys were investigated and the effect of second phase particle disp…

AZ31 magnesium alloy sheets (thickness 3 mm) were joined by TIG welding and the effect of two run rapid cooling friction stir processing (RC-FSP) on welded joint microstructure and mechanical properties was investigated. TIG welding was undertaken a…

Simultaneous double-sided friction stir welding (DFSW) experiments were undertaken on AMX 602 alloys (Mg, 6%Al, 0.5%Mn, 2%Ca) and the influence of diverse material flows caused by differing process parameters (rotation direction and travel speed) an…

Coupons with both triangular and rectangular gaps were prepared from AA 2024 aluminium alloy plate stock by friction stir welding (FSW) and volumetric defect formation was investigated by a neural network-based electronic NDE (e-NDE) technique. The …

An experimental study was carried out on friction stir welded aluminium alloy tailored welded blanks (TWB's) to determine mechanical properties and microstructural characteristics in order to evaluate friction stir welding (FSW) as a feasible method…

Following a description of the swept FSW spot welding process, experimental work on welding conditions is presented. A design of experiments (DOE) approach was employed to examine the effect of process parameters on unguided lap shear tensile streng…

Butt joints were fabricated in AA 6061-T6511 aluminium alloys by friction stir welding (FSW) and the influence of the welding equipment rigidity on their microstructure and mechanical properties was investigated. The experimental set-up incorporated…

Butt joints were fabricated in a Ruuki Optim 700 MC Plus microalloyed low carbon high strength complex phase steel (0.06%C, 1.79%Mn, 0.01%V, 0.08%Nb, 0.11%Ti) using one-sided and two-sided friction stir welding in order to investigate the difference…